Getting Familiar with Plumbing: A Must for Installing a Bathtub
Getting Familiar with Plumbing: A Must for Installing a Bathtub
Blog Article
The article down below pertaining to A Step-by-Step Guide to Installing a Bathtub is absolutely engaging. Give it a try and make your own personal ideas.
Setting up a bath tub isn't specifically brain surgery, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a moderately hard project. If the old bathtub is easily easily accessible, the project can move easily; if you need to open a wall surface to eliminate the old tub and also place the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and embeded in the new one. See to it you have actually certified yourself for the job and also are comfortable trying it. Instead of employing a contractor to take over a halfway-completed task, it is better to take into consideration using one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will certainly assist you set up a new bath tub in your shower room if you have already gotten a new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your tools and material list should consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the water system. After doing so, turn on the taps to drain any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be fairly troublesome because of the restricted gain access to that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly come from the pipes. When the supply pipes have been eliminated, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in area in between the faucet and the sink. Protect the faucet in position with the producer given backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous type ought to be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Making use of both wood boards under its feet, put the bathtub in the needed placement. The wood boards are handy in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the level and readjusting the feet on the bathtub until the spirit level reads level.
To install faucets, fit the bottom of the outermost versatile faucet port to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water supply and also examine all joints as well as brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the bathtub needs to wait up until the bath tub has been utilized a minimum of when as this will certainly settle it into its last setting.
Getting ready for the Installment
To start with, the supporting framework supplied with the bathroom ought to be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to stop pressure on the bath tub.
Fit the versatile tap ports to the bottom of both faucets using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last position.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to break a stiff seal, causing the water to permeate the wall between the bathroom and also the tiling, causing complications with moisture as well as feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to securing, to allow for the activity experienced when the bathtub remains in use. The sealer can break rather very early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very interested in A Step-by-Step Guide to Installing a Bathtub and I am hoping you liked the page. Liked our piece of writing? Please share it. Let someone else find it. I praise you for your time. Visit again soon.
Trust us, dial! Report this page